Blackberry Torch 9810 – Disassembling procedure – How to remove the mother board – How to remove the camera – Mobiles and Smartphones repair and service

Category: Mobiles and Smartphones Repair and Service 

Contents of this article 

  • How to remove the case 
  • How to remove the mother board 
  • How to remove the camera module

Blackberry Torch 9810

Remove the back cover of the phone
Remove the battery
Unscrew the four screws using the T6 screw driver
If you remove the screw in red, you void the warranty!
Remove front silver trim by using plastic opening tools and wiggle it off.
This is difficult to remove, but it should come off if you do it with caution.
Once you remove the rim cover, you should find two more screws on the top. Unscrew them using the T6 screw driver.
Use the plastic removal tool to remove the entire back cover.
Unplug the black antenna wire from the logic board.
Peel off the three ribbon cables
They are orange and located on each side as well as on the top of the logic board
The cable circled in yellow is glued to the silver cap. Pull the ribbon cable upward towards the battery area.
Take out your logic board
Camera Sensor
Use the Phillip screw driver to wiggle the camera sensor out.
Carefully remove this



Comments

Post a Comment

Popular posts from this blog

Low-Side MOSFET Drive Circuits and Techniques - 7 Practical Circuits

Image
In many circuits, it is necessary to use MOSFETs for switching. In many cases, the MOSFET drive signals are generated by microcontrollers. In other cases, they are generated by ICs – PWM controllers, timers or any IC in fact. However, MOSFETs cannot always just be connected to the drive signal and be expected to work properly. Due to the construction of the MOSFET, driving it is not the simplest of tasks, especially for beginners. There are many users who regularly ask for help on MOSFET drive related issues or problems on different blogs, websites and forums. So, here I will show some MOSFET drive techniques/methods for MOSFETs configured as low-side switches. Before I head on to MOSFET drive, let me just tell you what a low-side switch is, in case you don't know. When the MOSFET (that you're using as a switch) sinks current, it is a low-side switch. The load will be between the drain and +V supply. The source will be connected to ground. Gate will be driven with respect to gr
Read more

Using the SG3525 PWM Controller - Explanation and Example: Circuit Diagram / Schematic of Push-Pull Converter

Image
PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a
Read more

Simple MW Transmitter Circuit Diagram

Image
Today I'm going to give you a simple MW Transmitter.This transmitter can be operated with 9 v power supply.Here we have used common transistor BF494B.Here we have used MW antenna coil you can use the 8 ohm speaker to speak that means here the speaker does the work of the mic.To get the maximum result build this on a pcb and don't supply power without connecting the antenna.             Note:   Don't missuse this circuit            you can send signals up to 500M
Read more