Temperature sensor with PIC18 and MCP9700

 This can be a complete project on its own - a simple DIY digital thermometer with LCD display and only a handful of parts - the PIC18F45K20, LM35 and a small number of resistors and capacitors running off a regulated 5v supply.

Display type - LCD (can be 16x1, 16x2 or anything larger)
Controller: PIC18F45K20
Programming Language: BASIC
Compiler: mikroBASIC PRO for PIC v3.20

'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
'Programmer: Syed Tahmid Mahbub
'Compiler: mikroBASIC PRO for PIC v3.20
'Target PIC: 18F45K20
'Configuration: Check the project in the download link for the configuration bits


program MC9700_Temp

dim LCD_RS as sbit at RC4_bit
    LCD_EN as sbit at RC5_bit
    LCD_D4 as sbit at RC0_bit
    LCD_D5 as sbit at RC1_bit
    LCD_D6 as sbit at RC2_bit
    LCD_D7 as sbit at RC3_bit

    LCD_RS_Direction as sbit at TRISC4_bit
    LCD_EN_Direction as sbit at TRISC5_bit
    LCD_D4_Direction as sbit at TRISC0_bit
    LCD_D5_Direction as sbit at TRISC1_bit
    LCD_D6_Direction as sbit at TRISC2_bit
    LCD_D7_Direction as sbit at TRISC3_bit

dim ADRead as word
dim Temp as longword
dim vDisp as word[3]
dim Display as string[7]

main:
     TRISA = $FF
     TRISC = 0
     PORTC = 0
     LCD_Init()
     LCD_Cmd(_LCD_CURSOR_OFF)
     LCD_Cmd(_LCD_CLEAR)
     LCD_Out(1, 1, "Temp:")
     Display = "+125 'C"
     while true
           ADRead = ADC_Read(0)
           if (ADRead > 102) then 'If temperature is positive
              Temp = (100 * ( (10 * ADRead) - 1024 ) ) >> 11 'Get temperature
              Display[0] = "+"
           else 'If temperature is negative
              Temp = ( (1024 - (10 * ADRead) ) * 100 ) >> 11 'Get temperature
              Display[0] = "-"
           end if
           vDisp[0] = Temp div 100
           vDisp[1] = (Temp div 10) mod 10
           vDisp[2] = Temp mod 10
           Display[1] = vDisp[0] + 48
           Display[2] = vDisp[1] + 48
           Display[3] = vDisp[2] + 48
           LCD_Out(1, 8, Display) 'Show temperature
     wend
end.

 

Hex file + Schematic + Code freely available for download:
http://www.4shared.com/file/b8bT5a9e/MC9700_temperature_sensor.html

The code can be freely used and there is no copyright restrictions or anything as such. Only credit the author (me) where necessary.

Comments

Post a Comment

Popular posts from this blog

Low-Side MOSFET Drive Circuits and Techniques - 7 Practical Circuits

Image
In many circuits, it is necessary to use MOSFETs for switching. In many cases, the MOSFET drive signals are generated by microcontrollers. In other cases, they are generated by ICs – PWM controllers, timers or any IC in fact. However, MOSFETs cannot always just be connected to the drive signal and be expected to work properly. Due to the construction of the MOSFET, driving it is not the simplest of tasks, especially for beginners. There are many users who regularly ask for help on MOSFET drive related issues or problems on different blogs, websites and forums. So, here I will show some MOSFET drive techniques/methods for MOSFETs configured as low-side switches. Before I head on to MOSFET drive, let me just tell you what a low-side switch is, in case you don't know. When the MOSFET (that you're using as a switch) sinks current, it is a low-side switch. The load will be between the drain and +V supply. The source will be connected to ground. Gate will be driven with respect to gr...
Read more

Simple MW Transmitter Circuit Diagram

Image
Today I'm going to give you a simple MW Transmitter.This transmitter can be operated with 9 v power supply.Here we have used common transistor BF494B.Here we have used MW antenna coil you can use the 8 ohm speaker to speak that means here the speaker does the work of the mic.To get the maximum result build this on a pcb and don't supply power without connecting the antenna.             Note:   Don't missuse this circuit            you can send signals up to 500M
Read more

Using the SG3525 PWM Controller - Explanation and Example: Circuit Diagram / Schematic of Push-Pull Converter

Image
PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...
Read more